| |
| |
| |
|
Page: 1 2 3 4
Comments:
<0> what a strange person
<1> wasnt that kinda your prob too dirtydog?
<0> A shrub.
<2> nic?
<0> Perhaps.
<3> Is it possible to create a boot disk through windows?
<2> mine on the vaio was that i kept getting eth0 seeing 1394, and i had to active eth1 to see the nic
<0> The answer lies in the stars.
<0> Bugger off there and find it.
<1> wrong nic module or so?
<1> burn an iso joey
<2> one of my installs ran off of eth1, this current and the best one yet is now on eth0.
<4> Joeytgstk: what boot disk??
<5> i need sk98lin module instead of tulip
<5> anyone here use sk98lin module?
<4> conga: me
<3> No, bootable cd's aren't working
<3> Because my motherboard has an embedded version of drdos 7.03 on it
<1> what nic?
<5> A****aka, can you help me get it to work?
<3> piece of crap
<5> Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
<3> And it doesn't see fat32, or partitions over 2gb, so it doesn't even allow a boot cd to work
<1> if you cant boot up on cd..
<3> but a boot floppy works
<4> Joeytgstk: bootable CD work unless you have a computer where you shouln't install gentoo on it because it's too slow
<3> i tried mandriva, but it didn't detect my cdrom drive after booting
<4> conga: don't pm
<5> ok
<4> conga: modprobe sk98klin
<5> i compiled it into kernel
<4> if it don't work with that then it's the wrong module or unsupported
<4> BAD...
<4> compile as module
<5> bad?
<5> oh
<4> build in stuff seems to break :(
<1> congas nic is an evil nic
<5> lol
<5> it 's expensive
<5> i thought it's good
<5> i bought it for 29$
<1> pcie
<3> A****aka, any suggestions, this computer is far from too slow
<5> A****aka: CONFIG_SK98LIN=M?
<5> right?
<1> there are patches
<4> Joeytgstk: if it's far from being slow then there is a way to boot from the cd in the bios
<4> conga: you are editing the .config by hand??
<5> yeah
<4> you don't know the make menuconfig ?
<5> i did make menuconfig before
<5> i know
<3> A****aka: As soon as it tries to boot from cd it takes me to drdos
<4> Joeytgstk: look in your board manual, or call the maker, that is not normal
<4> or else there would be "no way" to install windows xp
<3> That's very true
<5> A****aka, can you paste me your /etc/config.d/net ?
<4> conga: why?
<5> i think mine setting is wrong
<5> i have a router
<6> conga: look into /etc/conf.d/net.example
<5> but i dont know which one to use
<6> conga: look into /etc/conf.d/net.example, use /etc/conf.d/net
<1> conga:
<6> .example means its an example
<6> :p
<1> i have a suggestion
<5> do i use dhcp?
<4> yes
<5> iface_eth0="dhcp
<5> "
<5> right?
<1> use make menuconfig
<1> and read the helps about the marvell nic
<5> do you think i need to get another card?
<1> no
<5> ok
<1> read the helps there i bet it says what module is the correct one
<1> if you understand what the `help`s are
<0> hey! I was talking to you!
<5> edit .config is much better
<1> says who?
<5> say me
<5> lol
<6> i think conga said
<7> make menuconfig && make && make modules_install owns
<7> *ownz
<1> a friend had marvell issues before
<1> so i noticed that there was a module not called sk98lin built for the marwell gigabit nics
<1> in the gentoo-sources
<1> all was told in the menuconfig help
<5> yes
<5> finally!!!!!! i got internet working
<5> lol
<5> :D
<5> yay
<8> ;)
<5> ehheee
<5> linux is very confusing
<5> lol
<5> how do i auto start the module at boot?
<6> built it in
<9> 0x01
<5> Autie build it in kernel?
<6> yes
<5> i built it as module
<5> like A****aka suggested
<6> not as 'M' but as '*'
<5> oh
<6> well, do you will always need it?
<9> put the module name in /etc/modules.autoload.d/kernel-2.x
<4> Autie: some modules fail to load when buld in...
<6> yeah
<6> well, i tell people my rule i always use: something you always need = built-in, something you don't need always = module
<6> but as you said
<6> when it fails, try it as module
<6> :)
<0> :)
<6> Psych: stop laughing at me
<0> Autie: spreekt vloms jong
<6> Psych: nope, this is an english channel
<0> Autie: spreekt vloms jong
<6> :/
<3> Bah
<3> Still nothing
<9> sUp3rT3h
<8> mmm chicken
<10> mmm fish
<5> :P
<0> pendulum you're looking especially shagworthy today
<11> Psych: LOOK WHAT YOU DID!
<0> Mank0r: ik ben zot
<11> no
<11> :(
<12> hellow
<0> sup Neaprocs
<8> Come on down, you're only going to hurt yourself.
<0> Hi lenox.
<13> lala
<0> hey! I was talking to you!
<5> yooooooooooo! :)
<5> i finally got gentoo working
<5> lol
<5> installation is piece of cake now! :)
<14> :P
<5> hehehe
<5> took me 2 days :)
<15> hmm... is it bad if i was called for dury juty and i only just opened the letter a month after i was supposed to turn up ?
Return to
#gentoo
or
Go to some related
logs:
terdaw
need correct key
oolite hyperspeed mass locked
#linux
fijutsu-siemens drivers
#java
#javascript
#linux
#windows
go to position in bufferedreader java
|
|