| |
| |
| |
|
Page: 1 2 3 4 5 6
Comments:
<0> what is boot properly? what is it doing exactly?
<1> well..
<1> nothing comes on the screen
<0> be descriptive :-)
<1> tne monitor is fine..
<1> ok
<0> ok what else? and beeps?
<1> so ive just got it recently...
<1> got some ecc registered ram..
<1> different kinds..
<1> got a psu
<0> stop.
<0> read my Q and answer them please.
<1> doesnt beep
<1> Post Code is AC in the end
<0> no beep no screen..
<0> reseat the AGP card.
<1> yes.. no beep no screen..
<1> onboard video
<1> worked fine before
<0> everything hooked up?
<0> drives, pci cards?
<1> added 2 extra drives to my data raid card.. no go
<1> yes
<0> pull it.
<1> ive reconnected everything
<1> i already pulled the card
<1> ive been at this all day
<0> pull it all. you want to start with the bare minimum.
<0> and add if you can.
<0> i'll help you now.
<1> so the only thing thats connected to the motherboard is the psu, cpus and the cables to start the system
<0> pull everything.. the only thing you will leve is the processor and heatsink.
<1> nother else
<1> ok
<0> do you have the power switch plugged into the motherboard pins?
<1> ok
<0> pull it and reseat it per the manual again.. double checking.
<1> so no noththing is plugged into the motherboard
<1> no ram just the cpus
<0> correct.
<1> what do you want me to reset?
<0> reset or re seat.. to take out and put back in.
<1> the motherboard?
<1> ?
<0> no i am explaining my terms.
<1> sorry im not understanding
<1> i just want to be clear on what to do..
<0> neither an i
<0> i've been qite clear.
<0> maybe..
<0> language barrier?
<1> you said to pull it and reset it..
<1> but what?
<1> <0> pull it and reseat it per the manual again.. double checking.
<0> reset = reseat.
<0> same difference.
<1> the cpu? the ram? motherboard?
<0> yes the power switch
<1> ok
<1> give me a min
<0> your making this harder than is needs to be..
<0> fine.
<0> back in two gotta pe
<0> back.
<1> ok
<0> ok so far. we have the cpu and heat sink attached to the mobo.. the power switch is attached. Next attach the PSU connector.
<1> 8 pin or 24 pin first
<1> ?
<0> 2 pin power switch.. from the case. then. any and all power connectors from the PSU that the mother board requires.
<1> ok
<1> doing that npow
<0> k
<1> ok done
<1> what now?
<0> once this is done... we attach the Keyboard and VGA cable from the monitor.
<1> done
<0> once that is done ***uming A/C cord from wall is in the psu press the power button.
<0> what happens?
<1> system turns on
<1> starts beeping
<1> post code is 00 on the motherboard
<1> as i know this means there is no ram
<0> good.
<1> it just keeps beeping 5 beeps
<0> turn it off..
<1> i did
<0> put in the ram.. and push the power button again .
<1> ok
<1> now it booted
<1> no beeps because of ram
<1> post code is "85"
<1> and it beeped 2 times when it got to "85"
<0> does the monitor initilize>?
<1> no
<1> nothing on the monitor
<0> do you have other ram to test/
<1> yes
<1> ive already tried that though
<0> please try other piece of ram please
<0> OH.
<1> ok
<0> when you put in the memory you only put in one stick right?
<1> no
<1> i put in 2
<1> one for each cpu
<0> DOH
<1> ?
<0> try with just one stick.
<0> start with Slot 1 on
<0> or 0
<0> how ever it's marked.
<2> damn it, one of my drives with photos on it is making this clicking sound, it shows up in bios as "0mb" it's a maxtor calypso drive. . damn it . ..
<0> AriNagel, did you maxblast it yet?
<0> my last click i dropped it from 3 feet and it ran for 3 days then poof.
<0> fat fingres 4 days.
<2> maxblast it?
<2> u serious?
<1> i did
<1> no go
<0> why not.. it it's showing 0 in the bios i'd say it's your last chance.
<0> kompakt, you have both voltage regulators in ?
<1> voltage regulators/
<1> what do you mean by that
<1> i dont get nothing on the screen
<1> monitor doesnt init at all
<0> do the cpu fans even come on?
<0> yes. they must..
<0> nm that Q
<0> have you tried just one processor/
<0> kompakt, where you fgo?
<0> when you tried just one memory on either side was it the same error message?
<1> ok
<1> i just removed the 2nd cpu
<0> and.. ? :-|)
<1> give me a sec
<0> ok
<0> back in a few gotta pee again.
<1> i get post code 85 again afer booting :/
<0> hmm try switching processors around.
<3> hey
<3> whats the term for when you put to much voltage into a device and then the device never works again?
<4> Does this mean frozen is leaving too?
<5> wtf
<5> what a lame chan
<4> lets go
<5> have fun loser
<3> **** you xank
<0> 30 minutes.. i'd say he's gone..
<1> it still doesnt work
Return to
#hardware
or
Go to some related
logs:
bios 62-0308
#politics
pfn_list_corrupt dell
#politics
kaspersky beeping
#beginner
smart guy sieres
#computers
There was a problem The system cannot find the file nic
bizarrecamgirls pass
|
|