| |
| |
| |
|
Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Comments:
<0> oh
<0> i thought you were supposed to screw in standoffs first
<0> then lay motherboard on it then use regular screw and screw it into top of standoff
<1> make damn sure there arent any standoffs that dont match up with a hole in the mobo
<0> nope they're all accounted for
<1> its not screwed down?
<0> i mean
<0> all the slots are accounted for with screws
<1> yeah, but the mobo is screwed down, right?
<0> yes
<1> k
<0> i installed in everything already, if i didnt screw it in, then the whole mobo would have fallen over already
<0> using only 1 stick of ram
<0> first dimm slot on left (green)
<0> what should i do now compdoc?
<1> power on?
<0> ok
<0> =/
<0> still nothinf displays
<0> what am i doing wronggggg
<1> you do have the heatsink/fan on?
<0> yes
<0> it poewrs on
<0> and its spinning
<0> the cpu fan right?
<1> yeah
<0> yes
<0> its running
<1> it worked for a while?
<0> i even got the fan mate running to it
<0> everything works until i turn off
<0> my psu
<0> cuz i cant just leave it running for no reason
<1> I mean, it booted once?
<0> everything turns on
<0> just no display on monitor
<1> did you ever see the boot screen?
<0> no
<1> dont suppose you have a pci vid card?
<0> yes i do
<0> and i already connected a power dongle to it
<1> does the system beep?
<0> no
<0> no beeps
<1> power dongle?
<0> yea a molex
<0> the molex has 2 female, one male connector
<1> pull the vid card and see if it beeps
<0> on it
<1> the speaker is connected?
<0> i heard clicks and stuff
<0> i'm not sure if i heard a beep
<0> dont think so
<0> no speakers are connected at the moment
<1> plug in the pci vid card, and swap the ram sticks
<0> i didnt think i needed to connect it until i brought it back into my room
<1> heh
<0> okay
<1> it wont beep then
<0> so should i connect my speakers?
<1> I mean the little case speaker
<1> unless it uses the external for beeps
<0> oh
<1> some do
<0> i connected a mini 4 pin female
<0> that says speaker to the mobo
<1> yeah
<0> okay then
<1> that one
<0> nice nice
<0> this mobo
<0> has onboard video
<0> it has a vga and dvi connector lol
<1> thats cool
<0> so i'm not sure to stick the monitor into my gfx or my mobo
<1> its an agp slot or pci-e
<0> my gfx = pci0e
<1> ok. unplug that card, and use the connector on the mobo
<0> ok
<0> i think
<0> it does beep
<0> low beep though
<1> hmm
<0> then i hear clicks so i ***ume its trying to access hd
<1> no image
<0> nope
<1> maybe your psu is bad
<0> dammit i dont want to rma stuff
<0> that means i haev to wait
<0> =/
<1> dont have a working pc you could borrow the psu from?
<0> i do but its only 300w
<0> this one is 500w new
<1> thats enough, if it has the right connector
<1> 24 pin
<1> disconnect all the drives - floppy, cd, hdd
<1> and the ribbon cables to them
<1> is the mouse and keyboard in the right holes?
<0> i'm using wireless
<0> should i revert to wired?
<1> might want to
<0> i haev a sata in sata1, and 2 ata.
<0> but i want the sata1 to be the master drive, while the 2 atas to slaves
<0> so i put jumper settings on sata as master, and the ata as slave
<0> using the ribbon cable i connected the ends to the 2 atas, despite one end of the ribbon cable being master
<1> sata dont use master/slave jumpers
<1> disconnect them all
<2> lol
<0> damn
<0> so i cant set my sata has master?
<0> and my atas as slaves?
<1> disconnect them all
<1> forget the drives
<1> even the floppy
<0> okay
<0> i disconnected all the drives
<0> now what?
<1> the power to them too?
<0> yes
<1> k
<1> power it up
<0> ok
<0> is it okay
<0> if i disonnect the ribbon cables
<0> but leave the ends connected to the mobo?
<1> better than nothing
<0> k
<1> any difference?
<0> no beeps thsi time
<1> its a socket 939?
<1> so its a 24 pin power connector? does the PSU have the right amount of pins?
<0> yes
<0> its a sock939, 24 pin, and psu has right amount
<1> k
<1> might unplug the connector and plug it back in
<1> wiggle it a little after to make sure its seated
<0> k
<0> i connected the keyboard
<0> the keyboard doesnt even ligjht up
<1> thats not good
<0> damnnnnn
<3> wtf
<3> argh
<4> I broke you?
<5> plz
<6> BwaaaaaaaahhhhhhKUMA! #computers..one of the few (only?) channel(s) where an FQDN can be banned by /notice-ing Akuma, master of the "I just ****-my-pants" ban. ROFL
<0> what are cpu jumbpers?
<4> yt-poo: depends...
<0> i just made a new pc
<4> on old computers they generally set the type of CPU, and clock rates
<0> everything powers up, nothing shows up on monitors =/
Return to
#computers
or
Go to some related
logs:
ebcd Dell perc
#sex
#netbsd
#politics
#nhl
HP laserjet only 1 copy prints
Heroism and Cowardess
#windows
it's a freaking os
#computers
|
|